Search results
From JRiverWiki
Create the page "JRSS" on this wiki! See also the search results found.
- The recommended option is to use JRSS mixing. JRSS is Media Center's built in remixer which performs a similar job to remixers See [[#Customising JRSS]] for further details.5 KB (864 words) - 16:20, 24 February 2018
- # NEW: JRSS surround sound processing is optional when converting 2 channel audio to 420 KB (3,139 words) - 10:20, 19 September 2010
- * Integrated with the JRiver audio engine, so all other features (JRSS, Room Correction, internal volume, Convolver etc.) are available3 KB (484 words) - 11:56, 26 March 2012
- Leave mixing set to JRSS v2.0 for the best quality output.6 KB (982 words) - 08:42, 20 September 2021
- * If the error occurs when playing multichannel or mono audio, be sure that [[JRSS]] is enabled in the [[Output Format]] DSP so that MC can mix to the proper7 KB (1,249 words) - 07:04, 21 August 2015
- 3. Fixed: JRSS downmixing was not always energy neutral when downmixing to mono.<br /> 7. Fixed: The phrase "JRSS Subwoofer (x Hz lowpass)" in Output Format configuration could not be172 KB (26,879 words) - 11:31, 5 August 2013
- ...eiver, then you select "No upmixing or downmixing." Otherwise, you select "JRSS." * You set Mixing to "JRSS"4 KB (666 words) - 12:59, 22 February 2015
- 10. Changed: When JRSS does center focused mixing (used for videos other than music videos), mono 7. Fixed: JRSS 5.1 to 7.1 upmixing could cause the stereo separation in the SL / SR channe171 KB (26,663 words) - 20:29, 1 March 2013
- 4. Fixed: JRSS downmixing could have too high of an output level.<br /> 5. Changed: Live television uses JRSS center-focused mixing for 2.0 to 5.1/7.1 conversion.<br />151 KB (23,401 words) - 20:35, 1 March 2013
- 1. Changed: By default JRSS and Bass Management will use 48 dB/octave cross-overs for the LFE / subwoof 3. Optimized: The low-pass and high-pass filters used for Bass Management, JRSS, etc. are about 38% faster.<br />163 KB (25,336 words) - 20:36, 1 March 2013
- ...xing" was disabled when selecting "Stereo", making it impossible to select JRSS v2.0 for 5.1 or 7.1 downmixing.<br /> 3. Fixed: JRSS v2.0 stereo to 4.0 mixing was not working properly (only applies to build 1149 KB (23,034 words) - 20:37, 1 March 2013
- 1. Fixed: DSP Studio had an extra semi-colon in the "JRSS ..." surround sound selection.<br /> 1. NEW: JRSS surround sound processing is optional when converting 2 channel audio to 4406 KB (63,091 words) - 22:53, 1 March 2013
- 4. Fixed: The phrase "JRSS Subwoofer (x Hz lowpass)" in Output Format configuration could not be27 KB (4,150 words) - 16:14, 26 September 2013
- 1. Fixed: JRSS downmix to mono erroneously adjusted the gain of the LFE in 19.0.125.<br /> 2. Fixed: JRSS downmixing could result in audio clipping due to the Peak Levels change in131 KB (20,651 words) - 01:07, 24 February 2023
- 1. NEW: Added a 3.1 output mode to JRSS (enabled with PCM or Dolby Digital). Feedback appreciated.<br />87 KB (13,985 words) - 18:43, 10 December 2019
- 1. Fixed: JRSS downmix to mono erroneously adjusted the gain of the LFE in 19.0.125.<br /> 2. Fixed: JRSS downmixing could result in audio clipping due to the Peak Levels change in1.92 MB (307,653 words) - 06:12, 24 February 2023
- ...ed: When picking extra channels so the output channel count was over eight JRSS channel mixing would not engage properly.<br> 1. NEW: Added a 3.1 output mode to JRSS (enabled with PCM or Dolby Digital). Feedback appreciated.<br />704 KB (112,081 words) - 01:00, 2 December 2023
- 4. Fixed: The phrase "JRSS Subwoofer (x Hz lowpass)" in Output Format configuration could not be41 KB (6,173 words) - 06:39, 24 February 2023
- ...ed: When picking extra channels so the output channel count was over eight JRSS channel mixing would not engage properly.<br>42 KB (6,713 words) - 14:09, 27 November 2023
- ...ed: When picking extra channels so the output channel count was over eight JRSS channel mixing would not engage properly.<br>36 KB (5,686 words) - 23:38, 14 November 2023
