Verifying DSP Studio

From JRiverWiki
Revision as of 13:42, 22 February 2018 by Mattkhan (talk | contribs)

Jump to: navigation, search

This Page is a Work in Progress

Overview

DSP Studio has a lot of options which interact with each other and it can be easy to make small mistakes that negatively impact sound quality. The ability to measure the output from Media Centre is therefore an extremely useful thing to be able to do. This page describes how to do this using freely available tools.

Platform Limitations

The ability to route external audio input through JRiver is only implemented on Windows.

Linux and MacOS users will need JRiver to play the test signal instead. This is described in [insert section here]

ASIO vs WDM

Windows users can choose between two input methods:

ASIO is typically preferred if the hardware supports it, this usually means you are using a pro audio interface.

Examples will be given using both methods.

Setup

Common Steps

Room EQ Wizard (REW)

Install REW from https://www.roomeqwizard.com/beta.html (note that the beta version is the generally recommended version to use)

Windows: WDM Setup

Media Centre

Ensure the feature is activated and working as per the instructions in WDM_Driver

Creating a MC -> REW Audio Path

The target signal chain is

Loopback Signal Chain

HifiCable

Install HifiCable from https://www.vb-audio.com/Cable/ (scroll to the bottom to find the HifiCable & ASIO Bridge package)

Open each audio device in the Windows Mixer in turn and ensure that each one is set to 2 channel, 24bit, 48000Hz operation

There are three devices to be configured

  • Hi-Fi Cable Playback

HifiCable Playback

  • Hi-Fi Cable Recording

HifiCable Recording

  • MC WDM Playback

MC Playback

Configure REW

Launch REW and open the preferences screen. Set the following options on the Soundcard tab

  • Drivers: Java
  • Sample Rate: 48kHz
  • Output Device: Default Device
  • Input Device: Hi-Fi Cable Output (VB-Audio Hi-Fi Cable)

Rew preferences.png

Configure MC

Launch MC and open the options screen, select the Audio page and choose the IPC zone. Set the following options;

  • Audio Device: Hi-Fi Cable Input (VB-Audio Hi-Fi Cable) [WASAPI]
  • Bitdepth: 24bit

NB: The bitdepth option is accessed via the "Device Settings..." option

Mc options.png

Open DSP Studio, deselect all blocks including output format.

Mc dsp passthrough.png

Verify the Signal Chain
  • Play a test signal
    • Launch REW
    • Open the Preferences screen
    • Go to the Soundcard tab
    • Select "Use Main Speaker test signal to check/set levels"
    • Click "Check Levels"
    • Click "Next >"
    • Confirm the output meter shows some signal is playing normally (NB: the input meters may also rise)

Rew output test.png

  • Verify MC is receiving and playing that signal
    • Open MC
    • Open DSP Studio
    • Go to the Analyser page
    • Check the analyser displays a wobbling straight line (i.e. is seeing and playing the test pink noise signal)

Mc output test.png

  • Verify REW is receiving the output from MC
    • Return to the REW Preferences/Soundcard tab
    • Check the input meters have risen to meet the input signal
    • Click "Finish" to stop the signal

Rew input test.png

  • Verify the end to end signal chain results in a passthrough, i.e. has flat frequency response
    • Close the REW Preferences screen
    • Click the "Measure" button
    • Set the following options
      • No Timing Reference
      • Start Freq: 2
      • End Pref: 24000
      • Level: -12.0
      • Length: 256k
      • Sweeps: 1
      • Output: Default Output/Both
    • Click "Start Measuring"
      • you should now see the measurement sweep complete normally and display a flat frequency response from 2-24kHz in the resulting SPL screen

Rew measure test.png