Id Install Guide

From JRiverWiki
Revision as of 15:28, 6 June 2014 by JimH (talk | contribs) (JimH moved page Id Instructions to Id Install Guide)

Jump to: navigation, search

Welcome

Thanks for using the JRiver Id. The name rhymes with "hid", and it is derived from an "imaginary device" that we first discussed a few years ago.

It has 120GB of SSD storage and 2GB of RAM. More specifications are on our wiki.

It works now as an audio player (DLNA / UPnP Renderer). You will play audio to it from a PC or Mac. The PC or Mac needs to run a DLNA Server (JRiver Media Center, for example, with the "Media Network" feature on). Other DLNA Servers should work.

Wires

Position the Id near your audio amplifier or other audio output. If you don't have a network there, consider using Ethernet over Powerline.

Connect an Ethernet cable (network), USB keyboard, power, and audio output (USB, HDMI, or 1/8" stereo analog).

At this time, an HDMI monitor must also be connected. It is possible to use the Id without a monitor, but it is more difficult to get it running.

Power

Turn the device on by pressing (not holding) the power button on the top. (See "Power" below if you need a different plug.) This same button is a safe way to shut down the Id (press, not hold).

In about 60 seconds, the Id should be running. If you have a monitor, you should see a text menu.

In another minute or two, the Id will show up under Playing Now in JRiver Media Center, running on your Mac or PC.

Network

The Id uses DHCP to get a network address. It requires a DHCP Server, which is commonly used on home networks.

One user has reported that the Id only works on port 52199. Ports 1024 and below can't be used since they require root privileges to change.

Options

The first time the Id is run, it defaults to HDMI audio out. You can use the text menu to change this if necessary.

At this time, the Id supports the Dragonfly USB DAC. Other USB DAC's may work if they present themselves as USB Audio Devices.

An option exists to turn on the DLNA Server. This allows you to play files from the Id, on other DLNA devices or in JRiver Media Center. To load files on the Id, use a Mac or PC and find the "Media" directory on the Id through your computer's network. The Id runs a Samba Server.

Updates are also available through this menu.

Menu

1 Analog Output *

2 HDMI *

3 USB DAC *

4 Toggle Media Server *

5 Set User Defined profile **

6 Check for Updates *

7 Network Status

8 GUI mode *

9 Headless Text mode *

10 Text Mode with HDMI Initialization *

98 Reboot

99 Shutdown


* Selecting this option will also reboot

** Saves any changes made in GUI mode so they are used when rebooted.

Powering Down

The Id uses very little electricity, but if you wish to turn it off, just press (not hold) the power button on the top.

Current Limitations

Though the NUC has capabilities for Wireless Ethernet, Bluetooth, and IR, these aren't available in the Id. They may be added later.

Running in the GUI mode may be less stable than using the text mode.

One user has reported that it only works on port 52199. Ports 1024 and below can't be used since they require root privileges to change.

Remote Control

Gizmo on Android or JRemote on iOS are supported. Other software remotes that work with JRiver Media Center may also work.

Connect to your source first, then choose to play to the Id.

Power

The Id has a switching power supply. It can use 100 to 240 volts and 50 to 60Hz.

It comes with adaptors for all common plugs. In the center of the picture below, there is a button with an arrow pointing to it. Press this button if necessary to exchange the plug for the one you need. You should find it in the Id's original package.

20140526 104255.jpg

Peripherals

The Id supports USB keyboards and mice. Logitech wireless keyboards and mice will work.

You can attach a monitor with an HDMI cable. DVI will also work, if you have an HDMI to DVI adaptor.

Common Problems

If the Id isn't available within five minutes, try rebooting. This can be done by pressing (not holding) the power switch.

If the Id is in Text Mode, and you can see the menu, but can't hear sound, try option 10, which reboots and initializes the HDMI display.

Text Mode may be more reliable than GUI mode at this time.

If MC stops running, it will be started automatically within one minute.

Questions?

Please use this thread on Interact.