Audio Setup: Difference between revisions

From wiki.jriver.com
Jump to navigation Jump to search
No edit summary
No edit summary
Line 1: Line 1:
==Configuring Audio Playback in Media Center==
==Configuring Audio Playback in Media Center==


This guide provides a high-level overview of how to best configure audio playback in Media Center. Follow the steps below in the order they are listed.
This guide provides an overview of how to configure audio playback in J. River Media Center. Please follow the steps below in order.




==Windows==
==Windows==


Start by making sure Windows recognizes your sound card. Always start with this step. If Windows can not use the device, no amount of futzing with Media Center will make things work.
Begin by verifying that Windows recognizes your sound card. If Windows cannot use the device, Media Center will not work.


Play test tones with Control Panel > Sound and ensure that you can hear them. This ensures that your device, speakers, volume, etc. are working.
In Control Panel > Sound, play test tones to ensure that you can hear them.


Remember the name of the sound card you are using so that you can select it in Media Center.
Remember the name of the sound card you use so that you can select it in Media Center.




Line 20: Line 20:
[[Audio Output Modes]]
[[Audio Output Modes]]


Also, in Options > Audio > Output mode settings..., select the name of the device you selected in the 'Windows' step above.
In Options > Audio > Output mode settings..., select the name of the device you used in the 'Windows' step above.




==Output Format==
==Output Format==


Open DSP Studio, and click on Output Format. Make sure it's enabled by placing a check mark in the box next to Output Format.
Open DSP Studio, and click on Output Format. Make sure it's enabled by checking the box next to Output Format.


Then, select these settings:
Then, select these settings:
Line 35: Line 35:
'''Channels'''
'''Channels'''


Set the channels selection to the number of outputs you are using from your computer. This is usually the same as the number of speakers you have attached. So for a 5.1 setup, select 5.1. For headphones, pick 2 channels. For desk speakers, pick 2 or 4 channels.
Set the channels selection to the number of outputs you are using from your computer. This is usually the same as the number of speakers you have attached. So for a 5.1 setup, select 5.1. For headphones, select 2 channels. For desk speakers, pick 2 or 4 channels.


Leave mixing set to JRSS v2.0 for the best quality output.
Leave mixing set to JRSS v2.0 for the best quality output.
Line 59: Line 59:
Once everything is working, you can use Room Correction to improve the sound.
Once everything is working, you can use Room Correction to improve the sound.


Open DSP Studio, and click on Room Correction. Make sure it's enabled by placing a check mark in the box next to Room Correction.
Open DSP Studio, and click on Room Correction. Make sure it's enabled by checking the box next to Room Correction.


Then, set the speaker distances for all the speakers you use.
Then, set the speaker distances for all the speakers you use.
Line 65: Line 65:
Next, play something that uses all the speakers.
Next, play something that uses all the speakers.


While playing, go through each speaker and tick the 'Level' checkbox at the bottom of the Room Correction page. Adjust the volume sliders until the level tones played by all speakers are the same volume. A decibel meter is best for this stage, but there are also apps that can use the microphone in your phone. You can also calibrate by ear and get passable results if you do not have a measurement device.
While playing, go through each speaker and tick the 'Level' checkbox at the bottom of the Room Correction page. Adjust the volume sliders until the level tones played by all speakers are the same volume. A decibel meter is best for this stage, but there are also apps that can use the microphone in your phone. You can also calibrate by ear and get passable results.


Finally, if you would like low frequencies to be routed to your subwoofer (bass management), configure the bass redirection portion of Room Correction for each speaker.
Finally, if you would like low frequencies to be routed to your subwoofer (bass management), configure the bass redirection portion of Room Correction for each speaker.

Revision as of 14:49, 21 June 2011

Configuring Audio Playback in Media Center

This guide provides an overview of how to configure audio playback in J. River Media Center. Please follow the steps below in order.


Windows

Begin by verifying that Windows recognizes your sound card. If Windows cannot use the device, Media Center will not work.

In Control Panel > Sound, play test tones to ensure that you can hear them.

Remember the name of the sound card you use so that you can select it in Media Center.


Audio Output Mode

In Media Center > Options > Audio, select the best audio output mode for your hardware.

Read more about this here: Audio Output Modes

In Options > Audio > Output mode settings..., select the name of the device you used in the 'Windows' step above.


Output Format

Open DSP Studio, and click on Output Format. Make sure it's enabled by checking the box next to Output Format.

Then, select these settings:

Sample rate

You only need to configure this if you play sample rates that are not supported by your hardware. For now, leave it on no resampling.

Channels

Set the channels selection to the number of outputs you are using from your computer. This is usually the same as the number of speakers you have attached. So for a 5.1 setup, select 5.1. For headphones, select 2 channels. For desk speakers, pick 2 or 4 channels.

Leave mixing set to JRSS v2.0 for the best quality output.

Bitdepth

Select the highest bitdepth your hardware supports (usually 24-bit)

Subwoofer

Leave default settings


Test

At this point, you should be able to play audio with Media Center. Start with simple tests like an MP3, APE, FLAC, or WAV played off of a local hard drive.

If this works, move on to more complex playback like Library Server Client, DLNA, Internet radio, etc.


Room Correction

Once everything is working, you can use Room Correction to improve the sound.

Open DSP Studio, and click on Room Correction. Make sure it's enabled by checking the box next to Room Correction.

Then, set the speaker distances for all the speakers you use.

Next, play something that uses all the speakers.

While playing, go through each speaker and tick the 'Level' checkbox at the bottom of the Room Correction page. Adjust the volume sliders until the level tones played by all speakers are the same volume. A decibel meter is best for this stage, but there are also apps that can use the microphone in your phone. You can also calibrate by ear and get passable results.

Finally, if you would like low frequencies to be routed to your subwoofer (bass management), configure the bass redirection portion of Room Correction for each speaker.